검색결과
-
[특집-기술위원회] TC 221 - 토목섬유(Geosynthetics)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 △1994년 TC 210, TC 211 △1996년 TC 213, TC 214 △1998년 TC 215~218 1999년 TC 219, TC 220 등이 있다.ISO/TC 221 토목섬유(Geosynthetics)와 관련된 기술위원회는 2000년 결성됐다. 사무국은 영국 표준협회(British Standards Institution, BSI)에서 맡고 있다.위원회는 데이비드 하이드 1세(Mr David I Hyde)가 책임지고 있다. 현재 의장은 피터 애치슨(Mr Peter Atchison)이며 임기는 2026년 말까지다.ISO 기술 프로그램 관리자는 안나 카테리나 로시(Dr Anna Caterina Rossi), ISO 편집 관리자는 타이나 비셰비치(Ms Tajna Biscevic) 등이다.범위는 지오텍스타일, 지오멤브레인, 토목합성재료 점토 차수재 및 기타 토목합성 관련 제품을 포함한 모든 토목합성 제품의 표준화다.현재 ISO/TC 221 사무국의 직접적인 책임 하에 발행된 표준은 47개며 ISO/TC 221 사무국의 직접적인 책임 하에 개발 중인 표준은 12개다. 참여하고 있는 회원은 30개국, 참관 회원은 16개국이다.□ ISO/TC 221 사무국의 직접적인 책임 하에 발행된 표준 47개 중 15개 목록▷ISO 9862:2023 Geosynthetics — Sampling and preparation of test specimens▷ISO 9863-1:2016 Geosynthetics — Determination of thickness at specified pressures — Part 1: Single layers▷ISO 9863-1:2016/Amd 1:2019 Geosynthetics — Determination of thickness at specified pressures — Part 1: Single layers — Amendment 1▷ISO 9864:2005 Geosynthetics — Test method for the determination of mass per unit area of geotextiles and geotextile-related products▷ISO 10318-1:2015 Geosynthetics — Part 1: Terms and definitions▷ISO 10318-1:2015/Amd 1:2018 Geosynthetics — Part 1: Terms and definitions — Amendment 1▷ISO 10318-2:2015 Geosynthetics — Part 2: Symbols and pictograms▷ISO 10318-2:2015/Amd 1:2018 Geosynthetics — Part 2: Symbols and pictograms — Amendment 1▷ISO 10319:2015 Geosynthetics — Wide-width tensile test▷ISO 10320:2019 Geosynthetics — Identification on site▷ISO 10321:2008 Geosynthetics — Tensile test for joints/seams by wide-width strip method▷ISO 10722:2019 Geosynthetics — Index test procedure for the evaluation of mechanical damage under repeated loading — Damage caused by granular material (laboratory test method)▷ISO 10769:2011 Clay geosynthetic barriers — Determination of water absorption of bentonite▷ISO 10772:2012 Geotextiles - Test method for the determination of the filtration behaviour of geotextiles under turbulent water flow conditions▷ISO 10773:2011 Clay geosynthetic barriers — Determination of permeability to gases□ ISO/TC 221 사무국의 직접적인 책임 하에 개발 중인 표준 12개 목록▷ISO/AWI 10318-1 Geosynthetics — Part 1: Terms and definitions▷ISO/AWI 10318-2 Geosynthetics — Part 2: Symbols and pictograms▷ISO/DIS 10319 Geosynthetics — Wide-width tensile test▷ISO/DIS 12236 Geosynthetics — Static puncture test (CBR test)▷ISO/DIS 12957-2 Geosynthetics — Determination of friction characteristics — Part 2: Inclined plane test▷ISO/FDIS 13426-2 Geotextiles and geotextile-related products — Strength of internal structural junctions — Part 2: Geocomposites▷ISO/DIS 13428 Geosynthetics — Determination of the protection efficiency of a geosynthetic against impact damage▷ISO/FDIS 13431 Geotextiles and geotextile-related products — Determination of tensile creep and creep rupture behaviour▷ISO/DIS 13433 Geosynthetics — Determination of dynamic perforation (cone drop test)▷ISO/CD TR 18228-5 Design using geosynthetics — Part 5: Stabilization▷ISO/DTR 18228-8 Design using geosynthetics — Part 8: Surface erosion control▷ISO/TR 18228-10 Design using geosynthetics — Part 10: Asphalt pavements
-
[특집-기술위원회] TC 219 - 바닥재(Floor coverings)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 △1994년 TC 210, TC 211 △1996년 TC 213, TC 214 △1998년 TC 215~218 등이 있다.ISO/TC 219 바닥재(Floor coverings)와 관련된 기술위원회는 1999년 결성됐다. 사무국은 벨기에 표준화기구(Bureau voor Normalisatie/Bureau de Normalisation, NBN)에서 맡고 있다.위원회는 카린 유핑거(Ms Karin Eufinger)가 책임지고 있다. 현재 의장은 제인 가드너(Ms Jane Gardner)이며 임기는 2024년 말까지다. ISO 기술 프로그램 관리자는 안나 카테리나 로시(Dr Anna Caterina Rossi), ISO 편집 관리자는 타즈나 비세빅(Ms Tajna Biscevic) 등이다.범위는 섬유, 탄력성 있는 바닥재 및 합판(라미네이트) 바닥재 분야의 표준화다. 단, 목재, 세라믹, 테라조, 콘크리트, 이중바닥재(악세스 플로어, Raised Access Floor)는 제외한다.현재 ISO/TC 219 사무국의 직접적인 책임 하에 발행된 표준은 83개며 ISO/TC 219 사무국의 직접적인 책임 하에 개발 중인 표준은 10개다. 참여하고 있는 회원은 29개국, 참관 회원은 17개국이다.□ ISO/TC 219 사무국의 직접적인 책임 하에 발행된 표준 83개 중 15개 목록▷ISO 1763:2020 Textile floor coverings — Determination of number of tufts and/or loops per unit length and per unit area▷ISO 1765:1986 Machine-made textile floor coverings — Determination of thickness▷ISO 1766:1999 Textile floor coverings — Determination of thickness of pile above the substrate▷ISO 1957:2000 Machine-made textile floor coverings — Selection and cutting of specimens for physical tests▷ISO 2094:1999 Textile floor coverings — Determination of thickness loss under dynamic loading▷ISO 2424:2007 Textile floor coverings — Vocabulary▷ISO 2549:1972 Textile floor coverings — Hand-knotted carpets — Determination of tuft leg length above the woven ground▷ISO 2549:1972/Cor 1:1990 Textile floor coverings — Hand-knotted carpets — Determination of tuft leg length above the woven ground — Technical Corrigendum 1▷ISO 2550:1972 Textile floor coverings — Hand-made carpets — Determination of types of knots▷ISO 2551:2020 Textile floor coverings and textile floor coverings in tile form — Determination of dimensional changes due to the effects of varied water and heat conditions and distortion out of plane▷ISO 3018:1974 Textile floor coverings — Rectangular textile floor coverings — Determination of dimensions▷ISO 3415:1986 Textile floor coverings — Determination of thickness loss after brief, moderate static loading▷ISO 3416:1986 Textile floor coverings — Determination of thickness loss after prolonged, heavy static loading▷ISO 4760:2022 Laminate flooring — Topical moisture resistance — Assembled joint▷ISO 4918:2016 Resilient, textile and laminate floor coverings — Castor chair test□ ISO/TC 219 사무국의 직접적인 책임 하에 개발 중인 표준 10개 목록▷ISO/FDIS 2424 Textile floor coverings — Vocabulary▷ISO/AWI 4918 Resilient, textile, laminate and modular mechanical locked floor coverings — Castor chair test▷ISO/CD 10833 Textile floor coverings — Determination of resistance to damage at cut edges using the modified Vettermann drum test▷ISO/CD 11378-2 Textile floor coverings — Laboratory soiling tests — Part 2: Drum test▷ISO/DIS 14486 Laminate floor coverings — Specification▷ISO/DIS 20251 Textile floor coverings — Water impermeability test▷ISO/CD 23106 Textile floor coverings — Production of changes in appearance by means of Vettermann drum tester▷ISO/CD 23122 Textile floor coverings — Production of changes in appearance by means of hexapod tumbler tester▷ISO/AWI 23999 Resilient floor coverings — Determination of dimensional stability and curling after exposure to heat▷ISO/FDIS 24342 Resilient and textile floor-coverings — Determination of side length, edge straightness and squareness of tiles and planks
-
[특집-기술위원회] TC 214 - 승강기 작업 플랫폼(Elevating work platforms)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 △1994년 TC 210, TC 211 등이 있다.ISO/TC 214 승강기 작업 플랫폼(Elevating work platforms)과 관련된 기술위원회는 TC 213과 마찬가지로 1996년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 샐리 사이츠(Ms Sally Seitz)가 책임지고 있다. 현재 의장은 스티븐 A. 베스트(Mr Stephen A. Best)이며 임기는 2029년 말까지다. ISO 기술 프로그램 관리자는 블란딘 가르시아(Mme Blandine Garcia), ISO 편집 관리자는 앤 기엣(Ms Anne Guiet) 등이다.범위는 용어, 등급, 일반 원칙(기술적 성능 요구 사항 및 위험 평가), 안전 요구사항, 테스트 방법, 유지관리, 승강에 사용되는 작업 플랫폼을 올리기 위한 조작 등의 표준화다. 또한 작업을 수행할 작업 위치에 직원(및 관련 작업 도구, 자재 등)을 배치에 대한 표준화도 포함된다.현재 ISO/TC 214 사무국의 직접적인 책임 하에 발행된 표준은 9개며 ISO/TC 214 사무국의 직접적인 책임 하에 개발 중인 표준은 3개다. 참여하고 있는 회원은 19개국, 참관 회원은 19개국이다.□ ISO/TC 214 사무국의 직접적인 책임 하에 발행된 표준 9개 목록▷ISO 16368:2010 Mobile elevating work platforms — Design, calculations, safety requirements and test methods▷ISO 16369:2007 Elevating work platforms — Mast-climbing work platforms▷ISO 16653-1:2008 Mobile elevating work platforms — Design, calculations, safety requirements and test methods relative to special features — Part 1: MEWPs with retractable guardrail systems▷ISO 16653-2:2021 Mobile elevating work platforms — Design, calculations, safety requirements and test methods relative to special features — Part 2: MEWPs with non-conductive (insulating) components▷ISO 16653-3:2011 Mobile elevating work platforms — Design, calculations, safety requirements and test methods relative to special features — Part 3: MEWPs for orchard operations▷ISO 18878:2013 Mobile elevating work platforms — Operator (driver) training▷ISO 18893:2014 Mobile elevating work platforms — Safety principles, inspection, maintenance and operation▷ISO 20381:2009 Mobile elevating work platforms — Symbols for operator controls and other displays▷ISO 21455:2020 Mobile elevating work platforms — Operator's controls — Actuation, displacement, location and method of operation□ ISO/TC 214 사무국의 직접적인 책임 하에 개발 중인 표준 3개 목록▷ISO/FDIS 16368 Mobile elevating work platforms — Design, calculations, safety requirements and test methods▷ISO/DIS 18878 Mobile elevating work platforms — Operator (driver) training▷ISO/DIS 18893 Mobile elevating work platforms — Safety principles, inspection, maintenance and operation
-
[특집-기술위원회] TC 213 - 치수와 기하학적 제품의 사양 및 검증(Dimensional and geometrical product specifications and verification)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 △1994년 TC 210, TC 211 등이 있다.ISO/TC 213 치수와 기하학적 제품의 사양 및 검증(Dimensional and geometrical product specifications and verification)과 관련된 기술위원회는 1996년 결성됐다. 사무국은 영국 표준협회(British Standards Institution, BSI)에서 맡고 있다.위원회는사라 켈리(Miss Sarah Kelly)가 책임지고 있다. 현재 의장은 이안 맥클라우드(Mr Iain Macleod)이며 임기는 2025년말까지다. ISO 기술 프로그램 관리자는 이사벨 베가(Ms Isabelle Vega), ISO 편집 관리자는 니콜라 페루(Ms Nicola Perou) 등이다.범위는 기하학적 제품 사양(GPS) 분야의 표준화다. 즉 치수 및 기하학적 공차, 표면 특성 및 관련 검증 원리, 치수 및 기하학적 측정의 불확실성을 포함한 측정 장비 및 교정 요구 사항을 다루는 거시 및 미세 형상 사양이다.표준화에는 기본 레이아웃과 도면 표시(기호)에 대한 설명이 포함된다. 단, 도면 표시(기호)의 특정 비율 및 치수 정의, 실행은 제외된다.현재 ISO/TC 213 사무국의 직접적인 책임 하에 발행된 표준은 147개며 ISO/TC 213 사무국의 직접적인 책임 하에 개발 중인 표준은 22개다. 참여하고 있는 회원은 26개국, 참관 회원은 25개국이다.□ ISO/TC 213 사무국의 직접적인 책임 하에 발행된 표준 147개 중 15개 목록▷ISO 1:2022 Geometrical product specifications (GPS) — Standard reference temperature for the specification of geometrical and dimensional properties▷ISO 286-1:2010 Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits▷ISO 286-1:2010/Cor 1:2013 Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits — Technical Corrigendum 1▷ISO 286-2:2010 Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts▷ISO 286-2:2010/Cor 1:2013 Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts — Technical Corrigendum 1▷ISO 463:2006 Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges▷ISO 463:2006/Cor 1:2007 Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges — Technical Corrigendum 1▷ISO 463:2006/Cor 2:2009 Geometrical Product Specifications (GPS) — Dimensional measuring equipment — Design and metrological characteristics of mechanical dial gauges — Technical Corrigendum 2▷ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out▷ISO 1119:2011 Geometrical product specifications (GPS) — Series of conical tapers and taper angles▷ISO 1660:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Profile tolerancing▷ISO 1938-1:2015 Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Plain limit gauges of linear size▷ISO 1938-2:2017 Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 2: Reference disk gauges▷ISO 2538-1:2014 Geometrical product specifications (GPS) — Wedges — Part 1: Series of angles and slopes▷ISO 2538-2:2014 Geometrical product specifications (GPS) — Wedges — Part 2: Dimensioning and tolerancing□ ISO/TC 213 사무국의 직접적인 책임 하에 개발 중인 표준 22개 중 15개 목록▷ISO/CD 1938-1 Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Plain limit gauges of linear size▷ISO/AWI 2768 General tolerances▷ISO/DIS 5059-1 Geometrical product specifications (GPS) — Dimensional measuring equipment: inside micrometers — Part 1: Two-point inside micrometers — Design and metrological characteristics▷ISO/FDIS 5459 Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems▷ISO/DIS 5463 Geometrical product specifications (GPS) — Form measuring equipment; Rotary axis form measuring instruments — Design and metrological characteristics▷ISO/CD 10360-102 Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 102: The language of symbols G3▷ISO/AWI 12179 Geometrical product specifications (GPS) — Surface texture: Profile method — Calibration of contact (stylus) instruments▷ISO/DIS 14405-1 Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes▷ISO/CD TS 15530-2 Geometrical Product Specifications (GPS) — Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement — Part 2: Part 2: Evaluating task-specific measurement uncertainty by multiple measurement strategies using a single uncalibrated workpiece▷ISO/DIS 16610-21 Geometrical product specifications (GPS) — Filtration — Part 21: Linear profile filters: Gaussian filters▷ISO/CD 16610-22 Geometrical product specifications (GPS) — Filtration — Part 22: Linear profile filters: Spline filters▷ISO/DIS 16610-31 Geometrical product specifications (GPS) — Filtration — Part 31: Robust profile filters: Gaussian regression filters▷ISO/DIS 16610-45 Geometrical product specifications (GPS) — Filtration — Part 45: Morphological profile filters: Segmentation▷ISO 18183-1 Geometrical product specifications (GPS) — Partition — Part 1: Vocabulary and basic concepts▷ISO/CD TR 23850 Geometrical product specifications (GPS) — Association — Mathematical concepts
-
[특집-기술위원회] TC 211 - 지리정보/지리학(Geographic information/Geomatics)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 등이 있다.ISO/TC 211지리정보/지리학(Geographic information/Geomatics)과 관련된 기술위원회는 TC 210과 마찬가지로 1994년 결성됐다. 사무국은 스웨덴 국립표준청(Svenska institutet för standarder, SIS)에서 맡고 있다.위원회는 마츠 올린(Mr Mats Åhlin)가 책임지고 있다. 현재 의장은 피터 파슬로(Mr Peter Parslow)이며 임기는 2024년말까지다. ISO 기술 프로그램 관리자는 하킴 음킨시(Mr Hakim Mkinsi), ISO 편집 관리자는 앨리슨 레이드 자몬드(Ms Alison Reid-Jamond) 등이다.범위는 디지털 지리정보 분야의 표준화다. 지구와 관련된 위치와 직간접적으로 연관된 물체나 현상에 관한 정보에 대한 구조화된 표준 세트 확립을 목표로 하고 있다.지리 정보의 범위 내에서 이러한 표준은 데이터 관리를 위한 방법, 도구 및 서비스를 지정할 수 있다. 데이터 관리는 사용자 및 시스템을 위한 데이터 획득, 처리, 분석, 접근, 제시 및 출판이 포함된다.이 작업은 가능한 경우 정보 기술 및 데이터에 대한 적절한 표준과 연결되어야 하며 지리 데이터를 사용하는 부문별 응용 프로그램 개발을 위한 프레임워크를 제공해야 된다.현재 ISO/TC 211 사무국의 직접적인 책임 하에 발행된 표준은 97개며 ISO/TC 211 사무국의 직접적인 책임 하에 개발 중인 표준은 26개다. 참여하고 있는 회원은 38개국, 참관 회원은 35개국이다.□ ISO/TC 211 사무국의 직접적인 책임 하에 발행된 표준 97개 중 15개 목록▷ISO 6709:2022 Standard representation of geographic point location by coordinates▷ISO 19101-1:2014 Geographic information — Reference model — Part 1: Fundamentals▷ISO 19101-2:2018 Geographic information — Reference model — Part 2: Imagery▷ISO 19103:2015 Geographic information — Conceptual schema language▷ISO 19104:2016 Geographic information — Terminology▷ISO 19105:2022 Geographic information — Conformance and testing▷ISO 19106:2004 Geographic information — Profiles▷ISO 19107:2019 Geographic information — Spatial schema▷ISO 19108:2002 Geographic information — Temporal schema▷ISO 19108:2002/Cor 1:2006 Geographic information — Temporal schema — Technical Corrigendum 1▷ISO 19109:2015 Geographic information — Rules for application schema▷ISO 19110:2016 Geographic information — Methodology for feature cataloguing▷ISO 19111:2019 Geographic information — Referencing by coordinates▷ISO 19111:2019/Amd 1:2021 Geographic information — Referencing by coordinates — Amendment 1▷ISO 19111:2019/Amd 2:2023 Geographic information — Referencing by coordinates — Amendment 2□ ISO/TC 211 사무국의 직접적인 책임 하에 개발 중인 표준 26개 중 15개 목록▷ISO/DIS 19103 Geographic information — Conceptual schema language▷ISO/CD 19109 Geographic information — General feature model and rules for application schema▷ISO/AWI TR 19115-4 Geographic information – Metadata — Part 4: JSON schema implementation of metadata fundamentals▷ISO/DIS 19116 Geographic information — Positioning services▷ISO/AWI TR 19121 Geographic information — Imagery and gridded data▷ISO/AWI 19123-2 Geographic information — Schema for coverage geometry and functions — Part 2: Coverage implementation schema▷ISO/AWI TS 19123-4 Geographic information — Schema for coverage geometry and functions — Part 4: Tiling Schema▷ISO/AWI TS 19124-2 Geographic information — Calibration and validation of remote sensing data and derived products — Part 2: SAR▷ISO/AWI 19127 Geographic information — Geodetic register▷ISO/AWI TS 19130-2 Geographic information — Imagery sensor models for geopositioning — Part 2: SAR, InSAR, lidar and sonar▷ISO/CD 19135 Geographic information registration — Requirements▷ISO/DTS 19144-3 Geographic information — Classification systems — Part 3: Land Use Meta Language (LUML)▷ISO/DIS 19152-2 Geographic information — Land Administration Domain Model (LADM) — Part 2: Land registration▷ISO/FDIS 19152-3 Geographic information — Land Administration Domain Model (LADM) — Part 3: Marine georegulation▷ISO/DIS 19152-4 Geographic information — Land Administration Domain Model (LADM) — Part 4: Valuation information
-
[특집-기술위원회] TC 210 - 의료기기를 포함한 건강 목적 제품의 품질 관리 및 이에 상응하는 일반적인 측면(Quality management and corresponding general aspects for products with a health purpose including medical devices스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~107 △1963년 TC 108~111 △1964년 TC 112~115, TC 117 △1965년 TC 118 △1966년 TC 119~122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146~150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~161 △1975년 TC 162~164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171~174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~186 △1984년 TC 188 △1985년 TC 189~191 △1988년 TC 192~194 △1989년 TC 195 △1990년 TC 197, TC 198 △1991년 TC 199, TC 201, TC 202 △1992년 TC 204~206 △1993년 TC 209 등이 있다.ISO/TC 210 의료기기를 포함한 건강 목적 제품의 품질 관리 및 이에 상응하는 일반적인 측면(Quality management and corresponding general aspects for products with a health purpose including medical devices)과 관련된 기술위원회는 1994년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 아미르 어바우탈레브(Mr Amir Aboutaleb)가 책임지고 있다. 현재 의장은 스콧 A. 콜번(Mr Scott A. Colburn)이며 임기는 2025년말까지다. ISO 기술 프로그램 관리자는 키르시 실란데르-반 후넨(Mrs Kirsi Silander-van Hunen), ISO 편집 관리자는 클라우디아 루에제(Ms Claudia Lueje) 등이다.범위는 액체 및 가스용 커넥터를 포함하는 건강 목적의 제품에 대한 품질 관리 및 상응하는 일반적인 측면과 관련한 분야의 요구 사항 및 지침에 관한 표준화다.단, △ISO/TC 176에서 다루는 일반 품질 관리 표준 △의약품 및 의료 서비스에 대한 품질 관리 표준은 제외한다.참고로 건강 목적의 제품에는 의료 기기, 인접 제품(또는 액세서리라고도 할 수 있음) 및 의료 기기와 유사한 위험 프로필을 가진 제품을 포함해 건강과 관련된 사용을 위한 제품이 포함된다.현재 ISO/TC 210 사무국의 직접적인 책임 하에 발행된 표준은 30개며 ISO/TC 210 사무국의 직접적인 책임 하에 개발 중인 표준은 13개다. 참여하고 있는 회원은 39개국, 참관 회원은 28개국이다.□ ISO/TC 210 사무국의 직접적인 책임 하에 발행된 표준 30개 중 15개 목록▷ISO 13485:2016 Medical devices — Quality management systems — Requirements for regulatory purposes▷ISO 14971:2019 Medical devices — Application of risk management to medical devices▷ISO 15223-1:2021 Medical devices — Symbols to be used with information to be supplied by the manufacturer — Part 1: General requirements▷ISO 15223-2:2010 Medical devices — Symbols to be used with medical device labels, labelling, and information to be supplied — Part 2: Symbol development, selection and validation▷ISO 18250-1:2018 Medical devices — Connectors for reservoir delivery systems for healthcare applications — Part 1: General requirements and common test methods▷ISO 18250-3:2018 Medical devices — Connectors for reservoir delivery systems for healthcare applications — Part 3: Enteral applications▷ISO 18250-6:2019 Medical devices — Connectors for reservoir delivery systems for healthcare applications — Part 6: Neural applications▷ISO 18250-7:2018 Medical devices — Connectors for reservoir delivery systems for healthcare applications — Part 7: Connectors for intravascular infusion▷ISO 18250-8:2018 Medical devices — Connectors for reservoir delivery systems for healthcare applications — Part 8: Citrate-based anticoagulant solution for apheresis applications▷ISO/TR 20416:2020 Medical devices — Post-market surveillance for manufacturers▷ISO 20417:2021 Medical devices — Information to be supplied by the manufacturer▷ISO/TR 24971:2020 Medical devices — Guidance on the application of ISO 14971▷IEC 62304:2006 Medical device software — Software life cycle processes▷IEC 62304:2006/Amd 1:2015 Medical device software — Software life cycle processes — Amendment 1▷IEC 62366-1:2015 Medical devices — Part 1: Application of usability engineering to medical devices□ ISO/TC 210 사무국의 직접적인 책임 하에 개발 중인 표준 13개 목록▷ISO/WD TS 5137 Medical device maintenance management for healthcare delivery organizations▷ISO 15223-1:2021/AWI Amd 1 Medical devices — Symbols to be used with information to be supplied by the manufacturer — Part 1: General requirements — Amendment 1▷ISO/AWI 15223-2 Medical devices — Symbols to be used with medical device labels, labelling, and information to be supplied — Part 2: Symbol development, selection and validation▷ISO/AWI 18250-3 Medical devices — Connectors for reservoir delivery systems for healthcare applications — Part 3: Enteral applications▷ISO 18250-8:2018/AWI Amd 1 Medical devices — Connectors for reservoir delivery systems for healthcare applications — Part 8: Citrate-based anticoagulant solution for apheresis applications — Amendment 1▷ISO/CD 20417 Medical devices — Information to be supplied by the manufacturer▷ISO/AWI 23421 Medical devices — Terminology — Terms used in the field of quality management and corresponding general aspects for products with a health purpose including medical devices▷ISO/CD TS 24971-2 Medical devices — Guidance on the application of ISO 14971 — Part 2: Machine learning in artificial intelligence▷ISO/DIS 80369-1 Small-bore connectors for liquids and gases in healthcare applications — Part 1: General requirements▷ISO/FDIS 80369-2 Small-bore connectors for liquids and gases in healthcare applications — Part 2: Connectors for respiratory applications▷IEC/AWI 80369-5 Small-bore connectors for liquids and gases in healthcare applications — Part 5: Connectors for limb cuff inflation applications▷ISO/DIS 80369-6 Small bore connectors for liquids and gases in healthcare applications — Part 6: Connectors for neural applications▷ISO/FDIS 80369-20 Small-bore connectors for liquids and gases in healthcare applications — Part 20: Common test methods
-
[특집-기술위원회] TC 201 - 표면 화학 분석(Surface chemical analysis)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186 △1984년 TC 188 △1985년 TC 189, TC 190, TC 191 △1988년 TC 192~TC 194 △1989년 TC 195 △1990년 TC 197, TC 198 등이 있다.ISO/TC 201 표면 화학 분석(Surface chemical analysis)과 관련된 기술위원회는 TC 199와 마찬가지로 1991년 결성됐다. 사무국은 일본 산업표준조사회(日本産業標準調査会, Japanese Industrial Standards Committee, JISC)에서 맡고 있다.위원회는 사토시 곤다(Dr Satoshi Gonda)가 책임지고 있다. 현재 의장은 히데히코 노나카(Dr Hidehiko Nonaka)이다.ISO 기술 프로그램 관리자는 주안우 주(Ms Chuanyu Zou), ISO 편집 관리자는 아룬 ABY 파라에카티(Mr Arun ABY Paraecattil) 등이다.범위는 표면 화학 분석 분야의 표준화다. 표면 화학 분석에는 전자, 이온, 중성 원자 또는 분자, 광자의 빔이 시료 재료에 입사되어 산란되거나 방출된 전자, 이온, 중성 원자 또는 분자, 광자가 감지되는 분석 기술이 포함된다.또한 표면 위로 스캔하는 조사 및 표면 관련 신호를 감지하는 기술도 포함하지만 ISO/TC 202의 범위 내에 있는 주사전자현미경은 제외한다.참고로 현재 표면 화학 분석 기술을 사용하면 분석 정보는 표면에서 가까운 영역(일반적으로 20 nm 이내)의 정보를 얻을 수 있다. 분석 정보 대비 깊이 데이터(analytical information-versus-depth data)는 더 깊은 표면 분석 기술을 사용해 얻을 수 있다.현재 ISO/TC 201 사무국과 관련해 발행된 표준은 81개며 ISO/TC 201 사무국의 직접적인 책임 하에 발행된 표준은 8개다.ISO/TC 201 사무국과 관련해 개발 중인 표준은 22개며 ISO/TC 201 사무국의 직접적인 책임 하에 개발 중인 표준은 2개다. 참여하고 있는 회원은 13개국, 참관 회원은 12개국이다.□ ISO/TC 201 사무국의 직접적인 책임 하에 발행된 표준 8개 목록▷ISO 14706:2014 Surface chemical analysis — Determination of surface elemental contamination on silicon wafers by total-reflection X-ray fluorescence (TXRF) spectroscopy▷ISO 16413:2020 Evaluation of thickness, density and interface width of thin films by X-ray reflectometry — Instrumental requirements, alignment and positioning, data collection, data analysis and reporting▷ISO 17331:2004 Surface chemical analysis — Chemical methods for the collection of elements from the surface of silicon-wafer working reference materials and their determination by total-reflection X-ray fluorescence (TXRF) spectroscopy▷ISO 17331:2004/Amd 1:2010 Surface chemical analysis — Chemical methods for the collection of elements from the surface of silicon-wafer working reference materials and their determination by total-reflection X-ray fluorescence (TXRF) spectroscopy — Amendment 1▷ISO 18337:2015 Surface chemical analysis — Surface characterization — Measurement of the lateral resolution of a confocal fluorescence microscope▷ISO/TS 18507:2015 Surface chemical analysis — Use of Total Reflection X-ray Fluorescence spectroscopy in biological and environmental analysis▷ISO/TR 19693:2018 Surface chemical analysis — Characterization of functional glass substrates for biosensing applications▷ISO 24465:2023 Surface chemical analysis — Determination of the minimum detectability of surface plasmon resonance device□ ISO/TC 201 사무국의 직접적인 책임 하에 개발 중인 표준 2개 목록▷ISO/AWI TR 4550 SCA –Surface chemical analysis of bacteria and biofilms▷ISO/FDIS 23124 Surface chemical analysis — Measurement of lateral and axial resolutions of a Raman microscope□ ISO/TC 201 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 201/SC 1 Terminology ; 발행된 표준 3개, 개발 중인 표준 0개▷ISO/TC 201/SC 2 General procedures ; 발행된 표준 9개, 개발 중인 표준 2개▷ISO/TC 201/SC 3 Data management and treatment ; 발행된 표준 5개, 개발 중인 표준 1개▷ISO/TC 201/SC 4 Depth profiling ; 발행된 표준 6개, 개발 중인 표준 0개▷ISO/TC 201/SC 6 Secondary ion mass spectrometry ; 발행된 표준 12개, 개발 중인 표준 2개▷ISO/TC 201/SC 7 Electron spectroscopies ; 발행된 표준 23개, 개발 중인 표준 5개 ▷ISO/TC 201/SC 8 Glow discharge spectroscopy ; 발행된 표준 6개, 개발 중인 표준 3개▷ISO/TC 201/SC 9 Scanning probe microscopy ; 발행된 표준 8개, 개발 중인 표준 4개▷ISO/TC 201/SC 10 X-ray Reflectometry (XRR) and X-ray Fluorescence (XRF) Analysis ; 발행된 표준 1개, 개발 중인 표준 3개
-
[특집-기술위원회] TC 199 - 기계류 안전(Safety of machinery)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186 △1984년 TC 188 △1985년 TC 189, TC 190, TC 191 △1988년 TC 192~TC 194 △1989년 TC 195 △1990년 TC 197, TC 198 등이 있다.ISO/TC 199 기계류 안전(Safety of machinery)과 관련된 기술위원회는 1991년 결성됐다. 사무국은 독일 표준화기구(Deutsches Institut für Normung e.V., DIN)에서 맡고 있다.위원회는 크리스티안 톰(Mr Dr. rer. nat Christian Thom)가 책임지고 있다. 현재 의장은 오토 괴르네만(Mr Otto Görnemann)이다.ISO 기술 프로그램 관리자는 메르세 페레 에르난데스(Mme Mercè Ferrés Hernández), ISO 편집 관리자는 클라우디아 루에제(Ms Claudia Lueje) 등이다.범위는 ISO/IEC 가이드 51 프레임워크 및 ISO, IEC 기술 위원회와 협력해 용어, 방법론, 보호 장치 및 안전 장치를 통합한 기계 안전에 대한 기본 개념 및 일반 원칙의 표준화다.단, ISO/IEC Guide 51에 정의되어 있고 다른 ISO 또는 IEC 기술 위원회의 작업에서 명시적으로 다루고 있는 제품 안전 표준은 제외한다.현재 ISO/TC 199 사무국의 직접적인 책임 하에 발행된 표준은 45개며 ISO/TC 199 사무국의 직접적인 책임 하에 개발 중인 표준은 9개다. 참여하고 있는 회원은 26개국, 참관 회원은 25개국이다.□ ISO/TC 199 사무국의 직접적인 책임 하에 발행된 표준 45개 중 15개 목록▷ISO Guide 78:2012 Safety of machinery — Rules for drafting and presentation of safety standards▷ISO 11161:2007 Safety of machinery — Integrated manufacturing systems — Basic requirements▷ISO 11161:2007/Amd 1:2010 Safety of machinery — Integrated manufacturing systems — Basic requirements — Amendment 1▷ISO 12100:2010 Safety of machinery — General principles for design — Risk assessment and risk reduction▷ISO 13849-1:2023 Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design▷ISO 13849-2:2012 Safety of machinery — Safety-related parts of control systems — Part 2: Validation▷ISO 13850:2015 Safety of machinery — Emergency stop function — Principles for design▷ISO 13851:2019 Safety of machinery — Two-hand control devices — Principles for design and selection▷ISO 13854:2017 Safety of machinery — Minimum gaps to avoid crushing of parts of the human body▷ISO 13855:2010 Safety of machinery — Positioning of safeguards with respect to the approach speeds of parts of the human body▷ISO 13856-1:2013 Safety of machinery — Pressure-sensitive protective devices — Part 1: General principles for design and testing of pressure-sensitive mats and pressure-sensitive floors▷ISO 13856-2:2013 Safety of machinery — Pressure-sensitive protective devices — Part 2: General principles for design and testing of pressure-sensitive edges and pressure-sensitive bars▷ISO 13856-3:2013 Safety of machinery — Pressure-sensitive protective devices — Part 3: General principles for design and testing of pressure-sensitive bumpers, plates, wires and similar devices▷ISO 13857:2019 Safety of machinery — Safety distances to prevent hazard zones being reached by upper and lower limbs▷ISO 14118:2017 Safety of machinery — Prevention of unexpected start-up□ ISO/TC 199 사무국의 직접적인 책임 하에 개발 중인 표준 9개 목록▷ISO/AWI 12100 Safety of machinery — General principles for design — Risk assessment and risk reduction▷ISO/DIS 12895 Safety of machinery — Identification of whole body access and prevention of associated risk(s)▷ISO/AWI 13849-2 Safety of machinery — Safety-related parts of control systems — Part 2: Guidance for the design and validation▷ISO/AWI TR 13849-3 Safety of machinery — Safety-related parts of control systems — Part 3: Markov model-based PFH calculation▷ISO/FDIS 13855 Safety of machinery — Positioning of safeguards with respect to the approach of the human body▷ISO/FDIS 14119 Safety of machinery — Interlocking devices associated with guards — Principles for design and selection▷ISO/AWI 14122-1 Safety of machinery — Permanent means of access to machinery — Part 1: Choice of fixed means of access between two levels▷ISO/AWI 14159 Safety of machinery — Hygiene requirements for the design of machinery▷ISO/CD TR 21260 Safety of machinery — Mechanical safety data for physical contacts between moving machinery or moving parts of machinery and persons
-
[특집-기술위원회] TC 198 - 보건 의료 제품의 멸균(Sterilization of health care products)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186 △1984년 TC 188 △1985년 TC 189, TC 190, TC 191 △1988년 TC 192~TC 194 △1989년 TC 195 등이 있다.ISO/TC 198 보건 의료 제품의 멸균(Sterilization of health care products)과 관련된 기술위원회는 TC 197과 마찬가지로 1990년 결성됐다. 사무국은 미국 표준협회(American National Standards Institute, ANSI)에서 맡고 있다.위원회는 아만다 베네딕(Ms Amanda Benedict)가 책임지고 있다. 현재 의장은 리차드 밴크로프트(Mr Richard Bancroft)이며 임기는 2025년 말까지다.ISO 기술 프로그램 관리자는 페트리샤 쿡(Mme Patricia Cook), ISO 편집 관리자는 클라우디아 루에제(Ms Claudia Lueje)등이다. 범위는 보건의료 제품의 멸균을 위한 프로세스 및 장비의 표준화다.현재 ISO/TC 198 사무국의 직접적인 책임 하에 발행된 표준은 69개며 ISO/TC 198 사무국의 직접적인 책임 하에 개발 중인 표준은 15개다. 참여하고 있는 회원은 34개국, 참관 회원은 21개국이다.□ ISO/TC 198 사무국의 직접적인 책임 하에 발행된 표준 69개 중 15개 목록▷ISO/TS 5111:2022 Guidance on quality of water for sterilizers, sterilization and washer-disinfectors for health care products▷ISO 11135:2014 Sterilization of health-care products — Ethylene oxide — Requirements for the development, validation and routine control of a sterilization process for medical devices▷ISO 11135:2014/Amd 1:2018 Sterilization of health-care products — Ethylene oxide — Requirements for the development, validation and routine control of a sterilization process for medical devices — Amendment 1: Revision of Annex E, Single batch release▷ISO 11137-1:2006 Sterilization of health care products — Radiation — Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices▷ISO 11137-1:2006/Amd 1:2013 Sterilization of health care products — Radiation — Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices — Amendment 1▷ISO 11137-1:2006/Amd 2:2018 Sterilization of health care products — Radiation — Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices — Amendment 2: Revision to 4.3.4 and 11.2▷ISO 11137-2:2013 Sterilization of health care products — Radiation — Part 2: Establishing the sterilization dose▷ISO 11137-2:2013/Amd 1:2022 Sterilization of health care products — Radiation — Part 2: Establishing the sterilization dose — Amendment 1▷ISO 11137-3:2017 Sterilization of health care products — Radiation — Part 3: Guidance on dosimetric aspects of development, validation and routine control▷ISO/TS 11137-4:2020 Sterilization of health care products — Radiation — Part 4: Guidance on process control▷ISO 11138-1:2017 Sterilization of health care products — Biological indicators — Part 1: General requirements▷ISO 11138-2:2017 Sterilization of health care products — Biological indicators — Part 2: Biological indicators for ethylene oxide sterilization processes▷ISO 11138-3:2017 Sterilization of health care products — Biological indicators — Part 3: Biological indicators for moist heat sterilization processes▷ISO 11138-4:2017 Sterilization of health care products — Biological indicators — Part 4: Biological indicators for dry heat sterilization processes▷ISO 11138-5:2017 Sterilization of health care products — Biological indicators — Part 5: Biological indicators for low-temperature steam and formaldehyde sterilization processes□ ISO/TC 198 사무국의 직접적인 책임 하에 개발 중인 표준 15개 목록▷ISO/DIS 11135.2 Sterilization of health care products — Ethylene oxide — Requirements for the development, validation and routine control of a sterilization process for medical devices▷ISO/FDIS 11137-1 Sterilization of health care products — Radiation — Part 1: Requirements for the development, validation and routine control of a sterilization process for medical devices▷ISO/CD 11140-3 Sterilization of health care products — Chemical indicators — Part 3: Class 2 indicator systems for use in the Bowie and Dick-type steam penetration test▷ISO/CD 11140-4 Sterilization of health care products — Chemical indicators — Part 4: Class 2 indicators as an alternative to the Bowie and Dick-type test for detection of steam penetration▷ISO/CD 11140-5 Sterilization of health care products — Chemical indicators — Part 5: Class 2 indicators for Bowie and Dick-type air removal tests▷ISO/AWI 11607-3 Packaging for terminally sterilized medical devices — Part 3: Requirements for process development for forming, sealing and assembly▷ISO/AWI 11737-1 Sterilization of health care products — Microbiological methods — Part 1: Determination of a population of microorganisms on products▷ISO/FDIS 15883-1 Washer-disinfectors — Part 1: General requirements, terms and definitions and tests▷ISO/DIS 15883-2 Washer-disinfectors — Part 2: Requirements and tests for washer-disinfectors employing thermal disinfection for critical and semi-critical medical devices▷ISO/DIS 15883-3 Washer-disinfectors — Part 3: Requirements and tests for washer-disinfectors employing thermal disinfection for human waste containers▷ISO/CD 15883-6 Washer-disinfectors — Part 6: Requirements and tests for washer-disinfectors employing thermal disinfection for noncritical medical devices and health care equipment▷ISO/DIS 15883-7 Washer-disinfectors — Part 7: Requirements and tests for washer-disinfectors employing chemical disinfection for non-critical thermolabile medical devices and health care equipment▷ISO/AWI TS 17664-3 Processing of health care products — Information to be provided by the medical device manufacturer for the processing of medical devices — Part 3: Guidance on the designation of a reusable medical device to a quantitative cleaning classification▷ISO 17665 Sterilization of health care products — Moist heat — Requirements for the development, validation and routine control of a sterilization process for medical devices▷ISO/AWI 19253 Sterilization of health care products — Application of ISO/TS 22421 to the requirements for sterilizers used for the terminal sterilization of health care products containing aqueous liquid in sealed containers
-
[특집-기술위원회] TC 195 - 건축 기계 및 장비(Building construction machinery and equipment)스위스 제네바에 본부를 두고 있는 국제표준화기구(ISO)에서 활동 중인 기술위원회(Technical Committeee, TC)는 TC 1~TC 323까지 구성돼 있다.기술위원회의 역할은 기술관리부가 승인한 작업범위 내 작업 프로그램 입안, 실행, 국제규격의 작성 등이다. 또한 산하 분과위원회(SC), 작업그룹(WG)을 통해 기타 ISO 기술위원회 또는 국제기관과 연계한다.ISO/IEC 기술작업 지침서 및 기술관리부 결정사항에 따른 ISO 국제규격안 작성·배포, 회원국의 의견 편집 등도 처리한다. 소속 분과위원회 및 작업그룹의 업무조정, 해당 기술위원회의 회의 준비도 담당한다.1947년 최초로 구성된 나사산에 대한 TC 1 기술위원회를 시작으로 순환경제를 표준화하기 위한 TC 323까지 각 TC 기술위원회의 의장, ISO 회원, 발행 표준 및 개발 표준 등에 대해 살펴볼 예정이다.이미 다룬 기술위원회와 구성 연도를 살펴 보면 △1947년 TC 1~TC 67 △1948년 TC 69 △1949년 TC 70~72 △1972년 TC 68 △1950년 TC 74 △1951년 TC 76 △1952년 TC 77 △1953년 TC 79, TC 81 △1955년 TC 82, TC 83 △1956년 TC 84, TC 85 △1957년 TC 86, TC 87, TC 89 △1958년 TC 91, TC 92 △1959년 TC 94 △1960년 TC 96, TC 98 △1961년 TC 101, TC 102, TC 104 등이다.또한 △1962년 TC 105~TC 107 △1963년 TC 108~TC 111 △1964년 TC 112~TC 115, TC 117 △1965년 TC 118 △1966년 TC 119~TC 122 △1967년 TC 123 △1968년 TC 126, TC 127 △1969년 TC 130~136 △1970년 TC 137, TC 138, TC 142, TC 145 △1971년 TC 146, TC 147, TC 148, TC 149, TC 150, TC 153 △1972년 TC 154 △1973년 TC 155 △1974년 TC 156~TC 161 △1975년 TC 162~TC 164 등도 포함된다.그리고 △1976년 TC 165, TC 166 △1977년 TC 167, TC 168, TC 170 △1978년 TC 171, TC 172, TC 173, TC 174 △1979년 TC 176, TC 178 △1980년 TC 180, TC 181 △1981년 TC 182 △1983년 TC 183~TC 186 △1984년 TC 188 △1985년 TC 189, TC 190, TC 191 △1988년 TC 192~TC 194 등이 있다.ISO/TC 195 건축 기계 및 장비(Building construction machinery and equipment)와 관련된 기술위원회는 1989년 결성됐다. 사무국은 중국 국가표준화관리위원회(国家标准化管理委员会, Standardization Administration of the P. R. C, SAC)에서 맡고 있다.위원회는 솽 리우(Mr Shuang LIU)가 책임지고 있다. 현재 의장은 징 리(Ms Jing Li)이며 임기는 2025년 말까지다. ISO 기술 프로그램 관리자는 몬자 코르터(Ms Monja Korter), ISO 편집 관리자는 이본느 헨(Mrs Yvonne Chen)등이다. 범위는 아래 내용을 포함한 건설 현장에서 사용되는 기계 및 장비 분야의 표준화다.표준화에 포함되는 내용은 △콘크리트 기계(예: 배처, 믹서, 펌프, 분무기, 운송, 진동기, 플로팅) △기초 기계(예: 말뚝 박기, 다이어프램 벽 설치, 흙 천공, 분사, 그라우팅, 토양 및 암석 혼합물용 드릴 장비) △골재 처리 기계(예: 스크리닝, 파쇄) △도로 건설 및 유지 관리 기계 및 장비 △터널 굴착 기계(TBM) 및 관련 기계 및 장비[예: 차폐 터널 보링 머신, 비차폐 터널 보링 머신, 텔레스코픽 쉴드 머신, 리머 머신, 마이크로 터널링 머신, 스러스트 보링 머신, 오거 보링 머신(채광용 제외), 에어록, TBM용 구조 챔버, 터널 보링 멀티서비스 차량(MSV)] △비계 등이다.또한 건축 자재의 생산 및 가공은 △자연석의 세공 △미세하고 무거운 점토 및 내화 세라믹 제조 △판유리, 중공유리, 특수유리의 생산, 처리, 가공 △현장에서 건축 자재를 처리하는 기계 및 장비 △도로 운영 기계 및 장비와 관련 서비스 △명명법 △애플리케이션 △분류 △평가 △기술 요구 사항 △테스트 방법 △안전 요구 사항 등을 포함한다.단, 고체 광물 물질 추출용 장비[예: 로드 헤더, 연속 광부, 착암기, 인상 천공기, 고벽 광부, LHD, 광산 오거 천공기), RMDS(신속 광산 개발 시스템)(ISO/TC 82)], 크레인(ISO/TC 96), 토공 기계 (ISO / TC 127), 승강 작업 플랫폼(ISO/TC 214), 건축 및 토목 공사(ISO/TC 59) 등은 제외한다.현재 ISO/TC 195 사무국과 관련해 발행된 표준은 39개며 ISO/TC 195 사무국의 직접적인 책임 하에 발행된 표준은 21개다.ISO/TC 195 사무국과 관련해 개발 중인 표준은 21개며 ISO/TC 195 사무국의 직접적인 책임 하에 개발 중인 표준은 8개다. 참여하고 있는 회원은 17개국, 참관 회원은 17개국이다.□ ISO/TC 195 사무국의 직접적인 책임 하에 발행된 표준 21개 중 15개 목록▷ISO 11375:1998 Building construction machinery and equipment — Terms and definitions▷ISO/TR 12603:2010 Building construction machinery and equipment — Classification▷ISO 15642:2003 Road construction and maintenance equipment — Asphalt mixing plants — Terminology and commercial specifications▷ISO 15643:2020 Road construction and maintenance equipment — Bituminous binder sprayers and synchronous bituminous binder sprayers-chip spreaders — Terminology and commercial specifications▷ISO 15644:2002 Road construction and maintenance equipment — Chippings spreaders — Terminology and commercial specifications▷ISO 15645:2018 Road construction and maintenance equipment — Road milling machinery — Terminology and commercial specifications▷ISO 15688:2012 Road construction and maintenance equipment — Soil stabilizers — Terminology and commercial specifications▷ISO 15689:2003 Road construction and maintenance equipment — Powder binder spreaders — Terminology and commercial specifications▷ISO 15878:2021 Road construction and maintenance equipment — Paver-finishers — Commercial specifications▷ISO 16039:2004 Road construction and maintenance equipment — Slipform pavers — Definitions and commercial specifications▷ISO 16039:2004/Amd 1:2013 Road construction and maintenance equipment — Slipform pavers — Definitions and commercial specifications — Amendment 1▷ISO 19432-1:2020 Building construction machinery and equipment — Portable, hand-held, internal combustion engine-driven abrasive cutting machines — Part 1: Safety requirements for cut-off machines for centre-mounted rotating abrasive wheels▷ISO 19433:2008 Building construction machinery and equipment — Pedestrian-controlled vibratory plates — Terminology and commercial specifications▷ISO 19452:2008 Building construction machinery and equipment — Pedestrian-controlled vibratory (percussion) rammers — Terminology and commercial specifications▷ISO 19452:2008/Cor 1:2008 Building construction machinery and equipment — Pedestrian-controlled vibratory (percussion) rammers — Terminology and commercial specifications — Technical Corrigendum 1□ ISO/TC 195 사무국의 직접적인 책임 하에 개발 중인 표준 8개 목록▷ISO/AWI 19432-2 Building construction machinery and equipment — Portable, hand-held, internal combustion engine-driven abrasive cutting machines — Part 2: Machines for abrasive chains — Safety requirements▷ISO/FDIS 20500-1 Mobile road construction machinery — Safety — Part 1: Common requirements▷ISO/FDIS 20500-2 Mobile road construction machinery — Safety — Part 2: Specific requirements for road-milling machines▷ISO/FDIS 20500-3 Mobile road construction machinery — Safety — Part 3: Specific requirements for soil-stabilising machines and recycling machines▷ISO/FDIS 20500-4 Mobile road construction machinery — Safety — Part 4: Specific requirements for compaction machines▷ISO/FDIS 20500-5 Mobile road construction machinery — Safety — Part 5: Specific requirements for paver-finishers▷ISO/FDIS 20500-6 Mobile road construction machinery — Safety — Part 6: Specific requirements for mobile feeders▷ISO/FDIS 20500-7 Mobile road construction machinery — Safety — Part 7: Specific requirements for slipform pavers and related machines□ ISO/TC 195 사무국 분과위원회(Subcommittee)의 책임 하에 발행 및 개발 중인 표준 현황▷ISO/TC 195/SC 1 Machinery and equipment for concrete work ; 발행된 표준 14개, 개발 중인 표준 4개▷ISO/TC 195/SC 2 Road operation machinery and associated equipment ; 발행된 표준 1개, 개발 중인 표준 1개▷ISO/TC 195/SC 3 Drilling and foundation machinery and equipment ; 발행된 표준 3개, 개발 중인 표준 8개